|
3
4
Welcome
Thank.you.for.purchasing.a.Uniden.Multi-Handset.phone.
Note:. Illustrations.in.this.manual.are.used.for.explanation.purposes..Some.illustrations.in.this.manual.may.differ.
from.the.actual.unit.
As.an.Energy.Star®.Partner,.Uniden.has.determined.that.this.product.or.product.models.meets.
the.Energy.Star®.guidelines.for.energy.efficiency..Energy.Star®.is.a.U.S..registered.mark.
Uniden.is.a.registered.trademark.of.Uniden.America.Corporation.
Accessibility
Uniden.provides.a.customer.service.hotline.for.accessibility.questions..If.you.have.a.disability.and.need.customer.
service.assistance.or.if.you.have.any.questions.about.how.Uniden’s.products.can.accommodate.persons.with.
disabilities,.please.call.the.accessibility.voice/TTY.line:.1-800-874-9314.
Our.customer.care.hours.as.well.as.accessibility.information.can.be.found.on.our.website,.www.uniden.com,.under.
the.“Accessibility”.link..If.your.call.is.received.outside.of.our.business.hours,.you.can.leave.us.a.message.and.we.will.
call.you.back.
May.be.covered.under.one.or.more.of.the.following.U.S..patents:
.
.
.
.
.
.
.
5,491,745.
5,671,248.
5,801,466.
5,960,358.
6,321,068.
6,889,184.
7,146,160.
5,533,010.
5,717,312.
5,825,161.
5,987,330.
6,418,209.
6,901,271.
7,203,307.
5,574,727.
5,732,355.
5,864,619.
6,044,281.
6,618,015.
6,907,094.
7,206,403.
5,581,598.
5,754,407.
5,893,034.
6,070,082.
6,714,630.
6,914,940.
7,310,398.
5,606,598.
5,758,289.
5,912,968.
6,076,052.
6,782,098.
6,940,867.
7,460,663
5,650,790.
5,768,345.
5,915,227.
6,125,277.
6,788,920.
6,953,118.
5,660,269.
5,787,356.
5,929,598.
6,253,088.
6,788,953.
7,023,176.
5,663,981
5,794,152
5,930,720
6,314,278
6,839,550
7,030,819
Other.patents.pending.
5
Installing the Phone
Choosing the Best Location
When.choosing.a.location.for.your.new.phone,.here.are.some.important.guidelines.you.should.consider:
PLACE YOUR BASE
TRY TO AVOID
• Microwave ovens
• Refrigerators
• Fluorescent
lighting
• Other cordless
telephones
Near an AC outlet and
a telephone wall jack.
• Personal computers
• Wireless LAN
equipment
• Areas with
a lot of
background
noise
• TVs
• Other electronics
• Dust
• Excessive
moisture
• Shock
• Vibration
In a centrally-located
open area.
• Direct sunlight
• Extreme temperatures
Notes:.For.maximum.range:.
•.Keep.both.the.base.and.handset.antennas.free.of.obstruction.
•.When.the.handset.is.not.in.use,.place.the.handset.in.an.upright.position.
•.Metal.and.reinforced.concrete.may.affect.cordless.telephone.performance.
6
Installing the Battery
Use.only.the.Uniden.BT-1007.or.BT-1015.rechargeable.battery.pack.supplied.with.your.cordless.telephone.
Unpack all handsets,
battery packs, and battery
covers. (If the battery cover
is on the handset, press in
on the notch and slide the
cover off.)
Line up the battery pack connector
with the jack inside the handset.
(The battery connector will only fit
one way.)
Push the battery pack
connector in firmly. (You
should hear it click into
place.) Gently tug on the
battery wires to make
sure the connection is
secure.
RED
BLACK
Place the cover over the
battery compartment
and slide it up into
place.
7
Connecting the AC adapter
To the base
To.avoid.risk.of.fire.and.shock,.only.use.the.Uniden.PS-0035.AC.adapter.with.the.base.
Connect the AC adapter to the AC IN 8V jack
on the back of the base.
Connect the AC
adapter to a
standard 120V
AC wall outlet.
Don’t put any power cord where people might
trip over it or step on it. If a power cord becomes
chafed or worn out, it can create a fire or
electrical hazard.
Route the cord through the
molded wiring channel.
To the DCX150 charging cradle (for multi-handset packs only)
Connect the AC adapter to the
Connect the AC adapter
to a standard 120V AC
wall outlet.
Use.only.the.Uniden
AC IN 8V jack as shown.
PS-0035.AC.adapter
(It may already be connected.)
with.the.DCX150
charging.cradle.
8
Charging the Handset
Place the handset in the base cradle with the
display facing forward.
If you have an accessory handset,
place it in the charging cradle with
the display facing forward.
Make sure that the charge
LED illuminates when the
handset is seated.
What if the charge LED doesn’t light up?
Reseat the handset; make sure the contacts
on the bottom of the handset are lined up
with the contacts in the charging cradle.
Check the AC adapter connection.
Make sure you are not using an outlet that’s
controlled by a wall switch.
Make sure that the charge
LED illuminates when the
handset is seated.
Charge your handset at least 15 to 20 hours before plugging into the phone line.
9
Connecting to the Phone Line
Make.sure.that.the.battery.pack.is.fully.charged.
Connect the telephone cord
to the TEL LINE jack.
What if Check
TEL Line
appears on the
handset display?
Connect the telephone
cord to a telephone
wall jack.
The telephone
cord may not be
connected
correctly. Check
the telephone
cord connection.
Telephone
wall jack
Telephone
cord
Do.you.have.DSL.or.any.high-speed.Internet.
service.delivered.through.your.phone.line?
Try.putting.a.DSL.filter.between.the.base.and.
the.wall.jack..Without.a.filter,.telephone-line-
based.Internet.services.can.interfere.with.
standard.phones.
DSL filter
10
Testing the Connection
Pick.up.the.handset.from.the.cradle.and.press.TALK/FLASH..You.should.hear.a.dial.tone,.and.the.display.
should.show.Talk.
What.if.I.can’t.hear.a.dial.tone?
Check.the.telephone.cord.connection.on.the.base.
What.if.the.display.doesn’t.show.Talk?.
•. Check.the.battery.pack.connection.in.the.handset.
•. Make.sure.the.battery.pack.is.fully.charged..
•. Make.sure.the.AC.adapter.cord.is.securely.connected.to.the..
AC IN 8V.jack.and.a.standard.power.outlet.
•. Try.resetting.the.handset.(see.page.51).
Make.a.quick.test.call,.and.then.press.END.to.hang.up..
What.if.there.is.a.lot.of.static?.
Check.the.sources.of.interference.described.in.Choosing.the.
Best.Location.(see.page.6):.is.the.base.near.any.of.those?
What.if.the.call.doesn’t.go.through?
Try.changing.the.dialing.mode.(see.the.next.section).
Note:. Make.sure.you.can.get.a.dial.tone.on.any.accessory.handsets.that.were.packaged.with.your.phone..
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
Changing the dial mode
Your.phone.can.communicate.with.the.telephone.network.in.two.different.ways:.tone.dialing.or.pulse.dialing..These.
days,.most.base.networks.use.a.method.called.tone.dialing,.so.your.phone.comes.programmed.for.tone.dialing..If.
your.phone.company.uses.pulse.dialing,.you.will.need.to.change.your.phone’s.dial.mode..If.you.don’t.get.a.dial.tone.
or.can’t.connect.to.the.telephone.network,.please.follow.the.steps.below.to.modify.your.phone’s.settings:
1).Press.MENU/SELECT..
2).Select.the.Global Setup.menu,.and.then.the.Dial Mode.submenu.
3).Scroll. .to.highlight.Pulse.
4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone.
If.you.ever.need.to.change.the.dial.mode.back.to.tone.dialing,.follow.the.same.procedure,.but.select.Tone.in.step.3.
NOW YOU ARE READY TO USE YOUR PHONE!
12
Expanding Your Phone
Adding accessory handsets
Your.phone.supports.a.total.of.six.cordless.handsets,.including.any.that.were.supplied.with.your.phone..You.can.now.
place.a.fully-featured.cordless.handset.anywhere.AC.power.is.available.to.connect.the.charging.cradle.
•.Your.phone.is.compatible.with.the.following.Uniden.DECT6.0.accessory.handsets:.DCX150,.DCX200,.and.
DCX300..(Please.visit.our.website.at.www.uniden.com.for.the.most.up-to-date.list.of.compatible.handsets.)
•.If.you.purchase.any.accessory.handsets.separately,.you.must.register.the.handsets.to.the.base.before.you.can.
use.them..(Accessory.handsets.that.come.packaged.with.a.base.are.already.registered.to.that.base.)
Registering accessory handsets
When.charged,.registered.handsets.display.a.handset.ID.number..Handsets.that.have.not.been.registered.display:
.. ..
↔
To.register.a.DCX150.accessory.handset:
1).Charge.the.handset.completely..(See.page.8.for.instructions.on.connecting.the.charger.and.page.9.for.
instructions.on.charging.the.handset.)
2).Place.the.handset.in.the.base.cradle.for.about.thirty.seconds..Handset Registering.will.appear.in.the.LCD.
3).When.the.handset.has.registered.to.the.base,.the.LCD.will.display.Registration complete.then.show.the.handset.
ID.number.
If.the.display.shows.Registration failed,.repeat.the.process.again..
To.register.a.DCX200.or.DCX300.accessory.handset:
1).Charge.the.handset.completely..(See.the.manual.supplied.with.the.accessory.handset.for.instructions.on.
connecting.the.charger.and.charging.the.handset.)
2).Disconnect.the.base.AC.adapter..Then.press.and.hold.FiND.while.you.reconnect.the.adapter..Keep.holding.
FiND.until.the.charge.LED.starts.to.blink.
13
3).On.the.handset,.press.and.hold.#.until.the.handset.beeps.and.displays.Handset Registering.
4).When.the.handset.has.registered.to.the.base,.the.LCD.will.display.Registration complete.then.show.the.handset.
ID.number.
If.the.display.shows.Registration failed,.repeat.the.process.again.
Note:. If.a.handset.has.ever.been.registered.to.a.base,.reset.the.handset.before.you.register.it.to.a.new.base.(see.
Using Multiple Bases
The.handsets.supplied.with.your.phone.can.be.registered.to.a.total.of.four.different.bases..Compatible.bases.include.
the.DECT1500.series.and.the.WXI2077.series..(See.our.website.or.contact.Customer.Service.for.an.up-to-date.list.
of.compatible.models.)
Note:. To.confirm.how.many.bases.the.handset.is.registered.to,.open.the.Select Base.submenu.(follow.the.step.1.of.
Selecting.the.base.on.page.15)..Press.END.to.close.the.list.and.return.to.standby.
Registering the handset to another base
To.register.a.handset.to.another.base:
1).Make.sure.the.handset.battery.is.fully.charged.
2).If.the.other.base.has.an.LCD.display:
•. With.the.phone.in.standby,.press.MENU/SELECT.on.the.base..Move.the.cursor.to.select.the.Register
Handset.menu,.and.then.press.MENU/SELECT..Handset Registering.will.appear.
If.the.other.base.does.not.have.an.LCD.display:.
•. Disconnect.the.base.AC.adapter..Then.press.and.hold.the.Find Handset.key*.while.you.reconnect.the.
adapter..Keep.holding.the.Find Handset.key.until.the.charge.LED.starts.to.blink.
*This.key.might.be.labeled.Find.or.Find HS.
3).On.the.handset,.press.MENU/SELECT..Select.the.Register Base.menu..Handset Registering.will.appear.in.the.
display..(After.step.2,.you.have.thirty.seconds.to.complete.this.step.3.before.the.system.returns.to.standby.)
14
4).Wait.approximately.thirty.seconds..Registration complete.will.be.displayed.to.indicate.the.handset.has.been.
registered.to.the.base.and.a.handset.ID.will.be.automatically.assigned..The.handset.assigns.its.own.ID.to.this.
base,.too..(Since.the.base.ID.is.based.on.the.order.in.which.the.handset.was.registered.to.the.different.bases,.a.
base.may.have.different.IDs.on.each.handset.)
If.Registration failed.appears.in.the.LCD,.please.try.these.steps.again.
Note:. The.handset.will.stay.connected.to.the.new.base.until.you.select.a.different.base.(see.below).
Selecting the base
After.you.register.your.handset.to.more.than.one.base,.you.can.set.the.handset.to.automatically.search.for.a.new.
base.if.the.base.it's.currently.connected.is.unavailable.or.out.of.range..You.can.also.manually.select.which.base.you.
want.the.handset.to.connect.to;.for.example,.if.you.have.one.base.with.an.answering.machine,.you.can.connect.to.
that.base.to.check.messages.from.the.handset.
1).With.the.phone.in.standby,.press.MENU/SELECT..Select.the.Handset Setup.menu,.and.then.the.Select Base.
submenu.
2).Move.the.cursor.to.select.the.base.you.want.to.connect.to,.or.choose.Auto.to.have.the.handset.automatically.
search.for.and.select.base.
3).Press.MENU/SELECT..Searching.will.appear.in.the.display.
4).When.the.base.is.found,.the.handset.will.return.to.standby..If.the.base.is.not.found,.“Searching”.continues.
to.appear..You.can.repeat.the.procedure.listed.above.to.return.back.to.the.original.connection.or.to.find.the.
different.base.
Note:. You.cannot.change.bases.during.a.call..
15
Getting to Know Your New Phone
Features
•.1.9GHz.DECT.6.0.expandable.system
•.Speakerphone.on.handset
•.7.ringer.options.on.handset.(3.tones/4.melodies)
•.Last.5.number.redial
•.Expands.up.to.6.handsets
•.Caller.ID/Call.Waiting.with.phonebook.match
•.Store.30.Caller.ID.numbers
•.Trilingual.menu.displays.(English,.Spanish,.or.French)
•.Call.transfer
•.70-number.phonebook.with.alphabetical.search
•.Personalized.ring.and.display.name.by.party
•.Transfer.single.listing.or.entire.phonebook
•.Conferencing
•.Intercom
16
Terminology Used in this Manual
Accessory
Handsets
Additional.handsets.that.can.register.to.the.base,.allowing.you.to.add.handsets.without.connecting.another.
phone.line..This.base.supports.a.total.of.six.cordless.handsets;.see.page.13.for.compatible.handsets.
Base
The.main.part.of.the.phone.that.connects.to.your.phone.line.and.lets.you.make.and.receive.calls.
Charging
cradle
A.cradle.that.comes.with.an.accessory.handset.and.charges.the.handset.battery.pack.
It.connects.to.power.but.does.not.connect.to.a.phone.line.
Caller.ID.is.available.from.your.telephone.provider.and.is.offered.to.users.on.a.subscription.basis.
With.this.service,.you.will.be.able.to.see.the.incoming.caller.information.such.as.name.and.phone.number.
CID
Caller.ID.with.Call.Waiting.is.available.by.subscription.from.your.telephone.provider.
With.this.service,.you.will.be.able.to.view.incoming.caller.information.while.on.a.call.with.another.user.
CID/CW
Any.settings.that.apply.to.all.registered.handsets.and.the.base.
These.features.are.available.by.selecting.“Global Setup”.or.“Day & Time”.in.the.handset.menu..Only.one.
handset.can.change.global.settings.at.a.time,.and.you.have.to.make.sure.the.phone.is.not.currently.being.
used..If.you.have.multiple.bases,.the.different.bases.have.each.global.settings;.select.the.base.before.
Global
Settings
The.handset.and.the.base.are.not.in.use..(It.doesn’t.matter.whether.the.handset.is.in.the.cradle:.the.TALK/
Standby
Talk
FLASH.or.
.hasn’t.been.pressed,.and.there.is.no.dial.tone.).
A.dial.tone.has.been.enabled,.so.you.can.dial.and.carry.on.a.conversation.with.an.outside.party.
Manual Conventions
This.manual.uses.several.different.type.styles.to.help.you.distinguish.between.different.parts.of.the.phone:
•.Bold italic text.indicates.a.key.or.button.on.the.phone
•.Italic.text.indicates.text.on.the.display,.such.as.menu.options,.prompts,.and.confirmation.messages
•.lower case bold.text.indicates.a.status.light.on.the.phone
•.ALL CAPITALS BOLD.indicates.a.connection.jack.on.the.base.or.charging.cradle
17
Parts of the Handset
new message LED
Earpiece
Display (LCD)
key (up)
CLEAR/INT'COM key
(clear/intercom)
MENU/SELECT key
Speakerphone
speaker and ringer
key (phonebook/left)
key (caller ID/right)
END key
TALK/FLASH key
key (down)
key (speaker)
Twelve-key dial pad
Battery compartment
/TONE key
# key
REDIAL/PAUSE key
Microphone
/MUTE key
(messages/mute)
Charging contacts
18
Using the Interface
Reading the Display
In standby
Time
During a call
6CNMꢀꢀꢀꢀꢀ2ꢀꢀ
ꢀꢁ1((ꢀꢂꢃꢁꢄꢄ#
ꢀꢀꢀ*CPFUGVꢀꢅꢂ
ꢀꢀꢀ0GYꢀ%+&ꢁꢀꢆ
Handset ID and banner
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢄꢁꢄꢄ
ꢀꢀꢀ
Call duration
Number of new
Caller ID calls received
The.ringer off.icon.indicates.that.the.ringer.is.turned.off.
The.voice mail.icon.appears.when.you.have.messages.waiting.in.your.voice.mailbox.
The.privacy.icon.appears.when.the.Privacy.Mode.is.turned.on.
The.speaker.icon.appears.when.the.speaker.phone.is.in.use.
The.T-coil.icon.appears.when.the.T-coil.Mode.is.turned.on.
The.mute.icon.appears.while.the.microphone.is.muted.
The.battery.icon.indicates.the.handset.battery.status:.full,.medium,.low,.and.empty.
20
Using the Four-way Function Key
Increase the volume
Your.handset.has.a.four-way.function.key.that.
allows.you.to.move.the.cursor.on.the.display.and.
access.the.most.commonly.used.features.at.the.
touch.of.a.button.
•.Press.the.left.side.of.the.key.to.open.the.
phonebook.
•.Press.the.right.side.of.the.key.to.open.the.
Caller.ID.list..
Open the
phonebook
Open the
Caller ID list
•.Press.the.top.of.the.key.to.increase.the.ringer.
volume.(while.the.phone.is.in.standby).or.
speaker.volume.(while.you.are.on.a.call).
•.Press.the.bottom.of.the.key.to.decrease.the.
ringer.volume.(while.the.phone.is.in.standby).
or.speaker.volume.(while.you.are.on.a.call).
Four-way
Function Key
Decrease the volume
Using the Handset Menu
•.To.open.the.menu,.press.the.MENU/SELECT.key.
•.The.arrow.cursor.on.the.left.side.of.the.line.shows.which.menu.item.is.currently.highlighted..Use.
way.function.key.to.move.the.cursor.up.and. .to.move.the.cursor.down.
•.To.select.the.highlighted.option,.press.MENU/SELECT.
on.the.four-
•.To.go.back.to.the.previous.screen,.press.left.on.the.four-way.function.key.
•.To.exit.the.menu,.press.END.
•.If.you.don’t.press.any.keys.for.thirty.seconds,.the.phone.will.time.out.and.exit.the.menu..(When.setting.the.day.
and.time,.the.time-out.period.is.extended.to.two.minutes.)
•.For.Global Setup.and.Day & Time.menu.options,.make.sure.the.line.is.not.in.use.and.the.handsets.are.within.
range.of.the.base.
21
Entering Text from Your Handset
You.can.use.the.number.keypad.on.your.handset.to.enter.text.by.referring.to.the.letters.printed.on.each.number.key..
When.you.press.the.number.key.in.a.text.entry.field,.the.phone.displays.the.first.letter.printed.on.the.number.key..
Press.the.number.key.twice.to.display.the.second.letter.and.three.times.to.display.the.third.
•.When.[Aa].appears.on.the.display,.capital.letters.are.displayed.first,.then.lower.case.letters,.and.then.the.number.
on.the.key.
•.When.[aA].appears.on.the.display,.lower.case.letters.are.displayed.first,.then.the.number.on.the.key,.and.then.
capital.letters.
•.When.you.input.the.first.letter.or.a.letter.after.a.blank.space,.the.default.mode.is.[Aa]..From.the.next.letter,.the.
mode.changes.to.[aA].automatically.
•.You.can.switch.back.and.forth.the.mode.manually.between.[Aa].and.[aA]..Press. /ToNE;.the.case.(small/capital).
of.the.letter.entered.changes.also.
If.two.letters.in.a.row.use.the.same.number.key,.enter.the.first.letter,.then.use right on.the.four-way.function.key.to.
move.the.cursor.to.the.next.position.to.enter.the.second.letter..
Number of times key is pressed (when [Aa] appears on the display)
For.example,.to.enter.the.word.“Movies”:.
1).Press.6.once.to.enter.M.
1
2 ABC
2).Use.right.on.the.four-way.function.key.to.move.the.
3 DEF
cursor.to.the.right.
4 GHI
3).Press.6.three.times.to.enter.o.
5 JKL
4).Press.8.three.times.to.enter.v.
6 MNO
7 PQRS
5).Press.4.three.times.to.enter.i.
8 TUV
6).Press 3.two.times.to.enter.e.
9 WXYZ
7).Press.7.four.times.to.enter.s.
0 OPER
8).Press.MENU/SELECT.to.end.your.text.entry.
If.you.make.a.mistake.while.entering.a.name,.use.right or.left on.the.four-way.function.key.to.move.the.cursor.to.the.
incorrect.character..Press.CLEAr/iNT’CoM.to.erase.the.wrong.character,.and.then.enter.the.correct.character..To.
delete.all.characters,.press.and.hold.CLEAr/iNT’CoM.
22
Basic Setup
Selecting a Language
Your.handset.supports.three.languages:.English,.French.and.Spanish..You.can.set.the.handset’s.language.
individually..Once.you.select.a.language,.the.menus.on.the.handset.will.display.in.that.language..The.default.
language.is.English.
1).Press.MENU/SELECT..
2).Select.the.Handset Setup.menu,.and.then.the.Handset Language.
*CPFUGVꢀ.CPIWCIG
submenu.
ꢀ'PINKUJ
3).Move.the.cursor.to.choose.English,.Français.(French).or.Español.
ꢀ(TCP㩟CKU
(Spanish).
4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone.
Setting the Time
To.change.the.time.shown.in.the.display,.follow.the.steps.listed.below.
1).Press.MENU/SELECT.
2).Move.the.cursor.to.Day & Time.and.press.MENU/SELECT.
ꢀꢀꢀ&C[ꢀꢁꢀ6KOG
3).Use. .and. .to.select.the.day.of.the.week,.and.press.MENU/
ꢀꢀ570ꢀꢂꢃꢄꢅꢅꢀ#/
SELECT.
ꢀꢀ=㨲ꢆ㨱ꢆUGNGEV?
Note:.The.day.of.the.week.does.not.appear.on.the.handset.display.
4).Use.the.number.keypad.(0.through.9).to.enter.the.hour.and.minutes.
5).Use. .and. .to.select.AM.or.PM,.and.press.MENU/SELECT..You.hear.a.confirmation.tone.
23
Activating Personal Ring
You.can.assign.special.ringer.tones.to.anyone.in.your.phonebook..When.your.phone.gets.a.call,.it.looks.up.the.
Caller.ID.information.in.your.phonebook..If.you’ve.assigned.a.personal.ringer.to.that.number,.the.phone.uses.it.so.
you.know.who.is.calling..To.turn.the.personal.ringing.on.or.off,.follow.these.steps:
1).Press.MENU/SELECT..
ꢀ2GTUQPCNꢀ4KPI
2).Select.the.Handset Setup.menu,.and.then.the.Personal Ring.
ꢀ1P
submenu.
ꢀ1HH
3).Move.the.cursor.to.select.On.or.Off.
4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone.
Activating the Key Touch Tone
Key.Touch.Tone.is.the.tone.your.keypad.makes.when.keys.are.pressed..You.can.turn.this.tone.on.or.off.
1).Press.MENU/SELECT..
Key Touch Tone
2).Select.the.Handset Setup.menu,.and.then.the.Key Touch Tone.
On
submenu.
Off
3).Move.the.cursor.to.select.On.or.Off.
4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone.
24
Setting Up the Phonebook
Each.handset.has.its.own.separate.phonebook.that.holds.up.to.seventy.names.and.numbers..When.a.handset’s.
phonebook.is.full,.the.handset.beeps.and.shows.Memory Full.on.the.display..You.cannot.add.any.names.and.
numbers.in.that.handset’s.phonebook.until.you.delete.some.of.the.existing.ones.
You.can.also.use.the.phonebook.entries.to.store.a.group.of.numbers.(up.to.twenty.digits).that.you.may.need.to.enter.
once.your.call.connects..This.is.referred.to.as.chain.dialing..(See.Chain.dialing.from.the.phonebook.on.page.32.)
Creating Phonebook Entries
To.store.names.and.numbers.in.your.phonebook,.please.follow.these.steps:
1).With.the.phone.in.standby,.press. .(on.the.left.side.of.the.four-way.key).
ꢀꢀꢀ'FKVꢀ0COG
2).To.create.a.new.phonebook.entry,.press.MENU/SELECT..Select.the.Create
㨫
New.menu..Edit Name.appears.
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ=#C?
3).Enter the name for this entry (EDIT NAME)..
Use.the.keypad.to.enter.a.name.for.this.entry;.the.name.can.contain.up.to.sixteen.characters..(See.Entering.
Text.from.Your.Handset.on.page.22.for.instructions.on.entering.text.).If.you.do.not.want.to.enter.a.name.for.this.
entry,.your.phone.will.store.this.entry.as.No Name..Press.MENU/SELECT.when.you.are.finished.
4).Enter the number for this entry (EDIT NUMBER).
Once.you.have.stored.a.name,.Edit Number.appears.next..Use.the.number.
keypad.to.enter.the.phone.number;.the.phone.number.can.contain.up.to.
twenty.digits..If.you.need.the.phone.to.pause.between.digits.when.it’s.dialing.
(for.example,.to.enter.an.extension.or.an.access.code),.press.rEDiAL/
ꢀꢀ'FKVꢀ0WODGT
ꢁꢂꢂꢃꢄꢂꢄꢅꢆꢇ㨫
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
PAUSE.to.insert.a.two-second.pause..You.will.see.a.P.in.the.display..You.can.
also.use.more.than.one.pause.together.if.two.seconds.is.not.long.enough..
Each.pause.counts.as.one.digit..Press.MENU/SELECT.when.you.are.
finished.
25
5).Assign a personal ring tone for this entry (PERSONAL RING).
You.can.attach.a.special.ring.tone.to.each.phonebook.entry;.the.phone.will.
use.this.ring.tone.when.this.person.calls..Use. .and. .to.select.one.of.
the.seven.different.ring.tone.options.(see.Selecting.a.Ring.Tone on.page.29.
for.a.complete.list.of.ring.tones)..As.you.scroll.through.the.tones,.you.will.
hear.a.sample.of.each.tone.(unless.the.handset.ringer.volume.is.set.to.off)..
When.you.hear.the.ring.tone.you.want.to.use,.press.MENU/SELECT..If.you.
do.not.want.to.use.a.personal.ring.tone.for.this.phonebook.entry,.choose.No
Selection;.the.phone.will.use.your.standard.ring.tone.setting.
ꢀ2GTUQPCNꢀ4KPI
ꢀ0Qꢀ5GNGEVKQP
ꢀ(NKEMGT
6).You.will.hear.a.tone.confirming.that.the.new.entry.has.been.stored,.and.Done!.appears.in.the.display.
Finding a Phonebook Entry
Press. .to.open.the.phonebook..Phonebook.entries.are.stored.in.alphabetical.order..To.scroll.through.the.
phonebook.from.A.to.Z,.press. ..To.scroll.through.the.phonebook.from.Z.to.A.press.
.
You.can.also.use.the.letters.on.the.number.keys.to.jump.to.a.name.that.starts.with.that.letter..For.example,.to.search.
for.an.entry.beginning.with.the.letter.M,.press.6.once..The.phonebook.jumps.to.the.first.entry.that.begins.with.the.
letter.you.entered;.you.can.then.use. .and. .to.scroll.to.other.entries.
To.close.the.phonebook.and.return.to.standby,.press.END..If.you.are.looking.up.a.phonebook.entry.during.a.call.and.
want.to.close.the.phonebook,.press. .again.instead.of.END.
Editing an Existing Phonebook Entry
1).With.the.phone.in.standby,.press. .to.open.the.phonebook.
2).Find.the.entry.you.want.to.edit.and.press.MENU/SELECT.
3).Select.Edit..Follow.the.steps.for.Creating.Phonebook.Entries.on.page.25..If.you.do.not.wish.to.change.the.
information.at.any.step,.simply.press.MENU/SELECT.to.go.to.the.next.step.
26
Storing Caller ID or Redial Numbers in the Phonebook
You.can.store.Caller.ID.records.or.redial.numbers.in.the.phonebook.so.you.can.use.them.later..Go.to.the.Caller.ID.or.
redial.list.and.select.the.number.you.want.to.store..(If.the.Caller.ID.information.did.not.include.the.number,.then.you.
will.not.be.able.to.store.it.)
1).With.the.phone.in.standby,.press. .to.open.the.Caller.ID.list.or.rEDiAL/PAUSE.to.open.the.redial.list.
2).Use. .and. .to.scroll.through.the.Caller.ID.records.or.redial.numbers..When.you.come.to.the.information.you.
want.to.store,.press.MENU/SELECT..
Note:..If.you.need.to.add.(or.delete).a.“1”.to.the.beginning.of.the.Caller.ID.phone.number,.press. /ToNE.(see.
.
.
page.33)..If.you.need.to.add.(or.delete).the.stored.area.code.to.the.Caller.ID.phone.number,.press.#.(see.
page.34).
3).Select.Store into PB..Edit Name.appears..If.the.phone.number.is.already.stored.in.memory,.you.will.hear.a.
beep,.and.This data is already saved!.appears.in.the.display..The.number.will.not.be.stored.
4).Continue.by.following.the.steps.for.Creating.Phonebook.Entries.on.page.25.
Deleting a Single Phonebook Entry
1).With.the.phone.in.standby,.press.
.
Edit
2).Find.the.entry.that.you.want.to.delete.and.press.MENU/SELECT..
3).Select.Delete..Delete Entry?.appears.in.the.display.
4).Move.the.cursor.to.select.Yes.
Copy
Delete
5).Press.MENU/SELECT..You.will.hear.a.confirmation.tone,.and.Deleted!.appears.in.the.display..
27
Deleting all Phonebook Entries
1).With.the.phone.in.standby,.press.
.
2).Press.MENU/SELECT,.and.then.select.Delete All..Delete All?.
ꢀ%TGCVGꢀ0GYꢀ
ꢀ%QR[ꢀ#NN
appears.in.the.display.
3).Move.the.cursor.to.select.Yes.
ꢀ&GNGVGꢀ#NN
4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone,.and.Deleted!.
appears.in.the.display.
Copying Phonebook Entries to Another Handset
If.you.have.more.than.one.handset,.you.can.transfer.phonebook.entries.from.one.handset.to.another.without.having.
to.re-enter.names.and.numbers..You.can.transfer.one.phonebook.entry.at.a.time.or.all.phonebook.entries.at.once.
1).With.the.phone.in.standby,.press. ..
2).To.copy.one.entry,.find.the.phonebook.entry.you.want.to.copy..Press.MENU/SELECT,.and.then.select.Copy.
To.copy.all.entries,.press.MENU/SELECT,.and.then.select.Copy All.
3).Move.the.cursor.to.select.the.handset.which.you.want.to.transfer.the.entries.to.and.then.press.MENU/SELECT.
If.you.select.Copy All, Are you sure?.appears.on.the.display.screen..Move.the.cursor.to.select.Yes,.and.then.
press.MENU/SELECT.
4).The.phonebook.entries.will.be.transferred.to.the.designated.handset..During.the.copy.process,.the.receiving.
handset.shows.Receiving.and.the.ID.of.the.sending.handset.
5).When.the.transfer.is.completed,.Done!.appears.on.the.handset.
.
•.If.the.handset.you.want.to.transfer.to.already.has.seventy.entries.in.its.phonebook,.you.will.hear.a.beep,.
and.Not enough memory in receiving unit.appears.on.the.display..
.
•.If.the.selected.handset.is.out.of.range.or.data.transfer.is.cancelled,.Unavailable.appears.in.the.display..
Phonebook.listings.will.not.be.transferred.
28
Customizing Your Handsets
All.of.the.following.options.are.set.separately.for.each.handset,.so.you.can.customize.a.handset.for.each.room.in.
your.house.
Changing the Handset Banner
Each.handset.will.display.a.banner.name.once.it.is.registered.to.the.base..The.
default.banner.is.Handset.#1,.Handset.#2,.etc..You.can.change.the.name.your.
phone.displays.by.changing.the.banner.display..If.you.have.more.than.one.handset,.
the.banner.name.identifies.your.handset.
1).Press.MENU/SELECT..
2).Select.the.Handset Setup.menu,.and.then.the.Banner.submenu.
3).Use.the.keypad.to.enter.or.edit.the.banner.name..(See.Entering.Text.from.Your.Handset.on.page.22.for.detailed.
instructions.on.entering.text.)
4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone.
Note:.. When.you.have.multiple.bases.and.even.if.the.handset.ID.is.changed.when.you.switch.to.a.different.base,.
the.handset.will.keep.the.banner.name.
Selecting a Ring Tone
You.may.choose.from.four.melodies.or.three.tones.for.your.
phone’s.primary.ring.tone..Each.handset.can.use.a.different.
ring.tone.or.melody..The.available.ring.tones.are.as.listed:
Fur.Elise.(Elise)
Flicker
Clatter
Wake.Up
We.Wish.You.A.Merry
Christmas.(Merry-Xmas)
Aura.Lee.(Aura Lee)
Star.Spangled.Banner
(Star Spngl)
Tones
Melodies
1).Press.MENU/SELECT..
2).Select.the.Handset Setup.menu,.and.then.the.Ringer Tones.submenu.
3).Move.the.cursor.to.select.a.ring.tone..As.each.ring.tone.is.highlighted,.you.will.
hear.a.sample.(unless.the.handset.ringer.volume.is.set.to.off).
4).When.you.hear.the.tone.you.want.to.use,.press.MENU/SELECT..You.will.hear.a.
confirmation.tone.
29
Activating AutoTalk
AutoTalk.allows.you.to.answer.the.phone.simply.by.picking.up.the.handset.from.the.cradle..You.do.not.have.to.press.
a.button.to.answer.the.call.
1).Press.MENU/SELECT..
2).Select.the.Handset Setup.menu,.and.then.the.AutoTalk.submenu.
3).Move.the.cursor.to.select.On.or.Off.
4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone.
Activating Any Key Answer
Any.Key.Answer.allows.you.to.answer.the.phone.by.pressing.any.key.on.the.twelve-key.dial.pad..
1).Press.MENU/SELECT..
2).Select.the.Handset Setup.menu,.and.then.the.Any Key Answer.submenu.
3).Move.the.cursor.to.select.On.or.Off.
4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone.
30
Using Your Phone
From a cordless handset
From a handset speakerphone
1).Pick.up.the.handset.from.the.cradle.
2).Press.TALK/FLASH.
1).Pick.up.the.handset.from.the.cradle.
2).Press.
.
3).Listen.for.the.dial.tone.
4).Dial.the.number.
3).Listen.for.the.dial.tone.
4).Dial.the.number.
Making
a call
OR
OR
1).Pick.up.the.handset.from.the.cradle.
2).Dial.the.number.
1).Pick.up.the.handset.from.the.cradle.
2).Dial.the.number..
3).Press.TALK/FLASH.
3).Press.
.
1).Pick.up.the.handset..(If.AutoTalk.is.on,.the.
phone.will.answer.when.you.pick.up.the.
handset.from.the.cradle.)
1).Pick.up.the.handset..
2).Press.
Answering
a call
2).Press.TALK/FLASH..(If.Any.Key.Answer.is.
on,.you.can.also.press.any.key.on.the.dial.
pad.)
.
Hanging up Press.END.or.return.the.handset.to.the.cradle.
31
Making a Call from the Phonebook
1).With.the.phone.in.standby,.press. .to.open.the.phonebook.
3).Press.TALK/FLASH.or. .to.dial.the.number.
Note:. You.can.also.press.TALK/FLASH.or. .before.you.open.the.phonebook..Find.the.phone.number.you.want.to.
dial,.and.then.press.MENU/SELECT.
Chain dialing from the phonebook
If.you.often.have.to.enter.a.series.of.digits.or.a.code.number.during.a.call,.you.can.save.that.code.number.to.a.
phonebook.entry..When.your.call.connects,.just.use.the.phonebook.to.transmit.the.saved.code.number..(This.is.
referred.to.as.chain.dialing.).
1).Enter.the.code.number.(up.to.twenty.digits).into.the.phonebook.(see.Creating.Phonebook.Entries.on.page.25)..
Be.sure.to.enter.the.code.number.into.the.phonebook.exactly.as.you.would.enter.it.during.a.call..
2).During.a.call,.when.you.hear.the.prompt.that.tells.you.to.enter.the.code.number,.press.
.
3).Use. .or. .to.select.the.phonebook.entry.that.contains.the.digits.you.want.to.send.
4).Press.MENU/SELECT..The.phone.sends.the.digits.of.the.code.number.exactly.as.you.saved.them.in.the.
phonebook.entry.
Switching to the Handset Speakerphone During a Call
To.switch.a.normal.call.to.the.speakerphone,.press. .on.the.handset..To.switch.from.a.speakerphone.call.to.a.
normal.call,.press.
.
32
Using Caller ID, Call Waiting, and Redial Lists
If.you.subscribe.to.Caller.ID.service.from.your.phone.company,.your.phone.will.show.you.the.caller’s.phone.number.
and.name.(if.available).whenever.a.call.comes.in..If.you.subscribe.to.Caller.ID.on.Call.Waiting,.the.phone.will.also.
show.you.the.name.and.the.number.of.any.call.that.comes.in.while.you’re.on.the.line.
Using the Caller ID List
You.can.store.up.to.thirty.Caller.ID.numbers.in.each.handset..Caller.ID.records.
are.stored.from.newest.to.oldest..Once.your.Caller.ID.list.is.full,.the.oldest.
record.will.be.automatically.deleted.when.a.new.call.is.received..When.you.
have.new.Caller.ID.records.(that.is,.records.you.have.not.reviewed.yet).and.the.
phone.is.in.standby,.the.handset.will.display.the.number.of.new.Caller.ID.calls.
received..(See.page.20.)
To.open.the.Caller.ID.list,.press.
.(on.the.right.side.of.the.four-way.key)..The.phone.will.show.the.latest.record..
Use. .and. to.scroll.through.the.list..(New.records.have.an.asterisk.next.to.the.received.time.)
Making a Call from a Caller ID Record
1).With.the.phone.in.standby,.press.
.to.open.the.Caller.ID.list.
2).Use. .and. .to.find.the.Caller.ID.record.you.want.to.dial.
3).If.you.need.to.add.(or.delete).a.“1”.to.the.beginning.of.the.displayed.phone.number,.press. /ToNE..
4).Press.TALK/FLASH.or. .to.dial.the.number.
Note:. You.can.also.press.TALK/FLASH.or. .before.you.open.the.caller.ID.list..Find.the.phone.number.you.want.
to.dial,.and.then.press.MENU/SELECT.
What’s.this.“add.or.delete.a.1”.about?
•.Any.phone.number.in.the.Caller.ID.records.might.(or.might.not!).have.a.“1”.at.the.front,.depending.on.how.
different.phone.companies.send.the.Caller.ID.information..
•.The.phone.dials.the.number.exactly.as.it.appears.in.the.Caller.ID.record..
•.If.the.phone.number.is.a.long.distance.or.toll.call,.but.the.Caller.ID.record.does.not.have.a.“1”.in.front.of.the.
number,.press. /ToNE.to.add.it..If.the.phone.number.is.a.local.or.non-toll.call,.but.the.Caller.ID.record.has.a.
“1”.in.front.of.the.number,.press. /ToNE.to.delete.it.
33
Seven-digit dialing
If.you.can.make.a.local.call.by.dialing.only.seven.digits.instead.of.ten,.you.can.tell.the.phone.to.hide.your.local.area.
code.in.the.Caller.ID.list;.any.calls.from.outside.your.area.code.will.show.all.ten.digits..This.setting.applies.to.the.
base.and.all.handsets.currently.connected.to.the.same.base.
To.program.your.local.area.code:
1).Press.MENU/SELECT..
2).Select.the.Global Setup.menu,.and.then.the.Area Code.submenu.
3).Use.the.number.keypad.(0.through.9).to.enter.a.three-digit.area.code..If.an.area.code.has.already.been.stored,.
it.appears.in.the.display..Press.CLEAr/iNT’CoM.to.delete.the.stored.code,.and.then.enter.a.new.one.
4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone.
Note:. If.you.have.multiple.bases,.select.the.base.before.programming.the.area.code.(see.page.15).
•.The.phone.uses.the.stored.area.code.as.a.filter..When.a.call.comes.in,.the.phone.compares.the.incoming.area.
code.to.the.code.programmed.on.the.phone..If.the.two.codes.match,.the.handset.hides.the.area.code.in.the.
Caller.ID.list.
•.When.you.are.reviewing.the.Caller.ID.list,.you.can.show.the.hidden.area.code.by.pressing.#..Press.#.again.to.
hide.the.area.code..
•.When.you.dial.from.a.Caller.ID.record.or.store.a.Caller.ID.record.in.the.phonebook,.the.phone.dials.or.stores.the.
digits.exactly.as.they.appear.on.the.display..If.you.need.to.use.ten.digits,.be.sure.to.press.#.to.show.the.area.
code.before.you.dial.or.store.the.number..(See.page.27.to.store.a.Caller.ID.record.in.the.phonebook.)
Deleting Caller ID Numbers
To.delete.only.one.Caller.ID.number,.press.
delete..Press.MENU/SELECT.and.select.Delete Entry..When.the.phone.asks.you.to.confirm,.select.Yes.
To.delete.all.the.Caller.ID.numbers,.press. .when.the.phone.is.in.standby..Press.MENU/SELECT.and.select.
.when.the.phone.is.in.standby,.and.then.find.the.number.you.want.to.
Delete All..When.the.phone.asks.you.to.confirm,.select.Yes.
Notes:.•.When.you.delete.a.Caller.ID.number,.you.delete.it.permanently.
.
•.Caller.ID.numbers.are.stored.separately.in.each.handset..Deleting.a.record.from.one.handset.will.not.delete.
the.record.from.any.other.handsets.
34
Using Call Waiting
If.you.have.Call.Waiting.service.and.a.second.call.comes.in.when.you.are.on.the.
phone,.a.call.waiting.tone.will.sound..Press.TALK/FLASH.to.accept.the.waiting.call..
There.is.a.short.pause,.and.then.you.will.hear.the.new.caller..To.return.to.the.original.
caller,.press.TALK/FLASH.
Note:.. You.must.subscribe.to.Call.Waiting.service.for.this.feature.to.operate..Not.all.
features.are.available.in.all.areas.
Redialing a Number
You.can.quickly.redial.the.last.five.numbers.dialed.on.each.handset.
1).With.the.phone.in.standby,.press.the.rEDiAL/PAUSE.to.open.the.redial.list.
2).Use. .and. .or.rEDiAL/PAUSE.to.scroll.through.the.redial.list.
3).When.you.find.the.number.you.want.to.dial,.press.TALK/FLASH.or.
.
Notes:.•.If.the.number.exceeds.32.digits,.only.the.first.32.digits.are.retained.in.redial.memory.
.
.
•.If.the.redial.memory.is.empty,.Empty.appears.in.the.display.and.you.will.hear.a.beep.
•.You.can.also.press.TALK/FLASH.or. .before.you.open.the.redial.list..Find.the.phone.number.you.want.to.
dial,.and.then.press.MENU/SELECT.
Deleting a Redial Record
If.you.want.to.delete.a.phone.number.from.the.redial.list,.follow.the.steps.below:
1).With.the.phone.in.standby,.press.rEDiAL/PAUSE.
2).Use. .and. .to.scroll.through.the.redial.list.
3).When.you.find.the.redial.number.you.want.to.delete,.press.MENU/SELECT.and.select.Delete Entry.
4).When.the.phone.asks.you.to.confirm,.select.Yes..The.redial.number.is.deleted.
35
Adjusting the Ringer, Earpiece and Speaker Volume
Adjusting the Ringer Volume
You.can.choose.from.four.ringer.volume.settings.(off,.low,.medium,.and.high).
separately.on.each.handset.
1).With.the.phone.in.standby,.press. .or. ..The.display.shows.the.current.
volume.level.and.the.handset.sounds.the.ringer.at.that.level.
2).Use. .to.make.the.ringer.volume.louder.or.use. .to.make.it.softer.or.turn.it.
completely.off.
3).When.you.hear.the.ringer.volume.level.you.want.to.use,.stop.pressing.keys..
The.handset.will.use.the.new.ringer.volume.starting.with.the.next.incoming.call.
Note:. If.you.set.the.ringer.volume.to.Off,.the.handset.won’t.ring..If.you.have.any.accessory.handsets,.other.
handsets.will.ring.according.to.their.individual.settings.
Muting the Ringer (One call only)
While.the.phone.is.ringing,.press. /MUTE.or.END.to.mute.the.ringer.for.this.call..The.phone.will.ring.again.on.the.
next.call..(The.handset.must.be.off.the.cradle.to.mute.the.ringer.)
Adjusting the Earpiece Volume
You.can.choose.from.six.volume.levels.for.the.handset.earpiece..To.adjust.the.earpiece.volume.while.on.a.call,.press.
.(to.make.it.louder).or. .(to.make.it.softer)..The.handset.display.shows.the.current.volume.level.for.the.earpiece.
Adjusting the Speaker Volume
You.can.choose.from.six.volume.levels.for.the.handset.speaker.while.on.a.speakerphone.call..To.adjust.the.handset.
speaker.volume,.press. .(to.make.it.louder).or. .(to.make.it.softer)..The.handset.display.shows.the.current.
volume.level.for.the.handset.speaker.
Note:. The.handset.earpiece.and.the.handset.speaker.have.separate.volume.settings.
36
Adjusting the Audio Tone
If.you.aren’t.satisfied.with.the.audio.quality.of.your.phone,.you.can.adjust.the.Audio.Tone.of.the.earpiece.while.on.
a.call..Your.phone.gives.you.three.audio.tone.options:.low,.natural.and.high;.the.default.setting,.Natural.Tone,.is.
recommended.for.hearing.aid.users..Audio.tone.adjustments.only.apply.to.the.earpiece,.not.the.speakerphone.
To.adjust.the.audio.tone:
1).While.on.a.call,.press.MENU/SELECT.
2).Move.the.cursor.to.select.Audio Tone,.and.then.press.MENU/SELECT.
3).Move.the.cursor.to.select.desired.option.(High Tone,.Natural Tone,.or.Low Tone),.and.then.press.MENU/
SELECT..Selected.option.appears.in.the.display.for.two.seconds,.and.then.the.display.returns.to.normal.
Activating T-Coil Mode
Digital.cordless.phones.generate.magnetic.signals.that.can.cause.noise.on.hearing.aids.equipped.with.a.telecoil.
(“T”.coil).feature..This.phone.includes.a.special.“T-coil”.mode.that,.when.activated,.reduces.the.magnetic.noise.
generated.by.the.handset.
1).With.the.phone.in.standby,.press.MENU/SELECT.
2).Select.the.Handset Setup.menu,.and.then.the.T-coil.submenu.
3).Move.the.cursor.to.select.On.or.Off.
4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone.
When.the.T-coil.mode.is.turned.on,. .appears.in.the.display.during.a.call.
Note:.. Using.the.T-coil.mode.may.shorten.the.handset.battery’s.talk.time;.make.sure.you.always.return.the.handset.
to.the.charging.cradle.when.not.in.use..Only.activate.T-coil.mode.if.you.experience.problems.using.the.
handset.with.a.T-coil-equipped.hearing.aid.
37
Finding a Lost Handset
To.locate.a.misplaced.handset,.press.FiND.on.the.base.when.the.phone.is.in.standby..The.handsets.connected.to.
the.paging.base.will.beep.for.one.minute,.and.PAGING.appears.on.the.handset.display..To.cancel.paging,.press.
FiND.again.or.any.key.on.the.found.handset.
Note:.. Handsets.that.are.not.currently.connected.to.this.base.will.not.be.paged.
Using Hold, Conference and Transfer
Placing a Call on Hold
1).During.a.call,.press.CLEAr/iNT’CoM.to.place.the.caller.on.hold..If.you.leave.a.caller.on.hold.for.more.than.ten.
seconds,.the.display.screen.will.read,.Line On Hold.
2).To.return.to.the.party.on.hold,.press.TALK/FLASH.or. ..The.phone.will.return.to.the.holding.party.
Notes:.•.You.can.only.place.a.caller.on.hold.for.five.minutes..Once.five.minutes.has.passed,.that.party’s.line.will.be.
disconnected.and.the.phone.will.return.to.standby.
.
•.While.a.call.is.on.hold,.Call.Waiting.and.CID.on.Call.
Waiting.do.not.work..
Outside call
Handset #2
Conferencing
If.you.have.more.than.one.handset,.up.to.three.people.can.
participate.in.a.conference.call..A.three-way.conference.call.
consists.of.an.outside.line.and.two.handsets..You.can.easily.
join.a.call.already.in.progress..The.handsets.must.be.currently.
1).Press.TALK/FLASH.or. .to.join.the.call.
2).To.hang.up,.return.the.handset.to.the.cradle.or.press.END..
Handset #1
The.other.party.will.still.be.connected.to.the.call.
38
Transferring a Call
You.can.transfer.a.call.from.one.handset.to.another..The.handsets.must.be.currently.connected.to.the.same.base.
(see.page.15).
1).During.a.call,.press.CLEAr/iNT’CoM.
2).Use. .or. .to.select.the.handset.you.want.to.transfer.the.call.to,.and.then.press.MENU/SELECT..Select.All.
to.page.all.other.handsets..The.call.will.automatically.be.placed.on.hold,.and.a.paging.tone.sounds..To.cancel.
the.transfer,.press.TALK/FLASH.or.
.
3).When.another.handset.accepts.the.transferred.call,.you.will.be.disconnected..If.you.want.to.rejoin.the.call,.press.
TALK/FLASH.or. .again.
Answering a transferred call
When.a.handset.receives.a.call.transfer,.it.sounds.a.paging.tone;.handsets.also.show.the.ID.of.the.handset.that.is.
paging..To.accept.the.call.transfer:
1).To.answer.the.page.and.speak.to.the.transferring.handset,.press.TALK/FLASH.or.CLEAr/iNT’CoM.
Note:. If.AutoTalk.is.on,.the.handset.will.automatically.answer.the.page.when.you.pick.up.the.handset.from.the.
cradle..If.Any.Key.Answer.is.on,.you.can.also.press.any.key.on.the.handset’s.dial.pad.
2).To.accept.the.call.and.speak.to.the.caller,.press.TALK/FLASH on.the.receiving.handset.
3).When.you.accept.the.transferred.call,.the.transferring.handset.will.be.disconnected.
Only.the.first.handset.to.answer.the.transfer.page.will.be.connected.to.the.call..If.the.transfer.page.is.not.picked.up.
within.one.minute,.the.operation.will.be.canceled.
39
Using Special Features
Privacy Mode
Privacy.mode.prevents.other.handsets.(that.are.connected.to.the.same.base).from.interrupting.your.call..As.long.as.
your.handset.is.in.privacy.mode,.other.handsets.can’t.join.your.call.or.make.any.calls.of.their.own:.their.displays.will.
show.Unavailable.
1).While.on.a.call,.press.MENU/SELECT.
2).Select.Call Privacy..Privacy Mode On.appears.in.the.display.for.two.seconds;. .appears.and.remains.in.the.
display.until.the.feature.is.turned.off.
To.turn.privacy.mode.off,.repeat.the.procedure.listed.above..Privacy Mode Off.appears.
Note:.Privacy.mode.does.not.affect.handsets.that.are.connected.to.a.different.base.or.extension.phone.
Using the Intercom
You.can.use.the.intercom.to.talk.to.another.handset.without.using.the.phone.line..The.handsets.must.be.currently.
Making an intercom page
1).With.the.phone.in.standby,.press.CLEAr/iNT’CoM.
2).Use. .or. .to.select.the.handset.you.want.to.talk.with,.and.then.press.MENU/SELECT..Select.All.to.page.all.
other.handsets.
3).To.cancel.the.intercom.page,.press.END.
Notes:.Intercom.paging.will.be.cancelled.if.any.of.the.following.things.occur:
•.You.receive.an.outside.call.or.an.intercom.page.while.selecting.the.other.handset.
•.You.do.not.select.a.handset.within.thirty.seconds.
•.Your.handset.is.out.of.range.(Out Of Range.appears.in.the.display).
•.The.party.does.not.answer.the.page.within.one.minute.
•.The.party.is.busy.
•.The.party.is.out.of.range.(Unavailable.appears.in.the.display).
40
Answering an intercom page
When.the.intercom.page.tone.sounds,.the.display.will.show.the.ID.of.the.handset.that.is.paging.
1).Press.TALK/FLASH.or.CLEAr/iNT’CoM.
Note:..If.AutoTalk.is.on,.the.handset.will.automatically.answer.the.page.when.you.pick.up.the.handset.from.the.
cradle..If.Any.Key.Answer.is.on,.you.can.also.press.any.key.on.the.handset’s.dial.pad.
2).To.hang.up.an.intercom.call,.press.END.
Muting the Microphone
Mute.turns.off.the.microphone.so.the.caller.can’t.hear.you..This.only.works.while.you.are.on.a.call..
1).Press. /MUTE..Mute On.and. .appear.in.the.display;. .remains.while.muting.is.on.
2).To.cancel.muting,.press. /MUTE.again..Mute Off.appears.
Tone Dialing Switch Over
If.your.phone.is.set.to.pulse.dialing,.you.can.temporarily.switch.to.tone.dialing.after.the.call.connects..This.feature.
is.useful.when.you.need.tone.dialing.to.use.automated.menu.systems,.such.as.telephone.bank.tellers,.telephone.
prescription.refills,.customer.support.menus,.etc..Make.your.call.normally..Once.your.call.connects,.press. /ToNE.
on.the.handset..Any.digits.you.enter.from.then.on.will.be.sent.with.tone.dialing..When.this.particular.call.ends,.the.
phone.automatically.returns.to.pulse.dialing.
See.Changing.the.dial.mode.on.page.12.for.instructions.on.setting.your.phone.for.pulse.or.tone.dialing.
41
Using a Voice Mail Service
If.you.subscribe.to.a.voice.mail.service,.you.can.use.your.phone.to.access.your.voice.mailbox..When.there.are.
messages.waiting.in.your.voice.mailbox,.the.new message.LED.on.the.handset.flashes,.and. .appears.in.the.
handset.display..
If.you.program.your.access.number.into.your.phone,.you.can.simply.press. /MUTE.to.access.your.voice.mail..Your.
voice.mail.service.provider.should.provide.you.with.the.access.number,.signaling.tone,.and.other.specifics.when.you.
enroll.
Setting the voice mail signaling tone
If.you.are.having.trouble.with.your.message.waiting.indicator.on.your.phone.not.illuminating.when.you.have.waiting.
messages,.you.will.need.to.contact.your.service.provider.and.inquire.as.to.which.type.of.message.notification..
signal.—.either.Frequency.Shift.Keying.(FSK).or.Stutter.Dial.Tone.(SDT).—.their.service.uses.
If.your.voice.mail.service.uses.an.FSK.message.signal.to.alert.you.of.a.new.voice.mail.message,.you.must.turn.
off.the.Voice.Mail.Tone..If.your.voice.mail.service.uses.an.SDT.message.signal.to.alert.you.of.new.voice.mail.
messages,.you.can.leave.the.Voice.Mail.Tone.on.
Follow.the.instructions.below.to.set.up.your.cordless.phone.settings:
1).Press.MENU/SELECT..Select.the.Global Setup.menu,.and.then.the.Voice
8QKEGꢀ/CKNꢀ6QPG
Mail Tone.submenu.
ꢀ1P
2).Move.the.cursor.to.set.the.SDT.Voice.Mail.Tone.to.On.or.Off.
ꢀ1HH
3).Press.MENU/SELECT..You.hear.a.confirmation.tone.
42
Programming one-touch voice mail access
You.can.program.your.voice.mail.access.number.to.the.Voice.Mail.key. /MUTE.on.each.handset.so.you.can.get.
your.messages.at.the.touch.of.a.button..Your.voice.mail.service.provider.will.supply.you.with.the.access.number.(this.
may.be.simply.a.phone.number).
To.edit.the.voice.mail.number,.follow.the.steps.below:
1).Press.MENU/SELECT.
2).Move.the.cursor.to.select.the.Handset Setup.menu.and.press.
ꢀ'ꢀFꢀKVꢀ8AOCKNꢀ0Qꢁ
MENU/SELECT.
㨫
3).Move.the.cursor.to.select.Edit Voice Mail.and.press.MENU/SELECT.
4).Enter.your.personal.access.number.(up.to.twenty.digits)..If.you.need.to.have.
the.phone.wait.before.sending.the.next.digits,.press.rEDiAL/PAUSE.to.
insert.a.two-second.pause.in.the.dialing.sequence..For.a.longer.pause,.press.rEDiAL/PAUSE.multiple.times..A.
P.appears.in.the.display.each.time.you.press.rEDiAL/PAUSE.and.each.pause.counts.as.one.digit.
5).Press.MENU/SELECT.when.you.are.finished..You.will.hear.a.confirmation.tone.
Resetting the voice message waiting indicator
When.you.receive.a.new.voice.mail.message,.the.new message.LED.on.the.top.of.the.handset.flashes.and. ..
appears.in.the.handset.display..In.the.event.your.message.waiting.light.gets.out.of.sync.with.your.phone.company’s.
voice.messaging.system,.you.can.manually.reset.it.back.to.the.“No.messages.waiting”.state.
1).Press.and.hold.FiND.on.the.base.for.five.seconds..
Note:.The.handsets.connected.to.the.base.will.start.to.beep,.however,.keep.pressing.for.five.seconds.
2).A.beep.sounds.and.the.message.alert.tone.is.reset.
43
Wall Mounting the Base
This.phone.can.be.mounted.on.any.standard.telephone.wall.plate.using.an.optional.wall-mount.bracket..You.can.
purchase.a.wall-mount.bracket.by.calling.the.Uniden.Parts.Department..(See.the.back.cover.page.for.contact.
information.)
Route the telephone cord through the hole of
the wall-mount bracket.
Connect the AC adapter and the telephone
cords as shown on pages 8 and 10.
Line up the four tabs on the wall-mount
bracket (two at the top and two at the
center) with the four notches on the
bottom of the base.
Slide the bracket into place.
Let the AC adapter cord
hang below the base.
Wall plate
Plug the telephone
cord into the wall jack.
Tuck the excess cord
into the open space in
the bracket.
(To AC outlet)
44
Place the mounting slots over
the pins on the wall plate.
Slide the base
down to lock it
into place.
Wall plate
(To AC outlet)
Note:. Mounting.the.phone.directly.on.the.wall
Removing the wall-mount bracket
•. Be.sure.the.wall.is.capable.of.supporting.the.
weight.of.the.phone,.and.use.the.proper.type.of.
anchoring.device.for.the.wall.material.
At the bottom of the base,
pinch the two "nose" of
the wall-mount bracket
as shown, and then
slide the bracket away
from the base.
•. Insert.two.#10.screws.(minimum.length.of.1.3/8.
inches,.not.supplied).into.the.wall,.3.15/16.inches.
apart...
•. Leave.the.screw.heads.1/8.inch.away.from.the.
wall.to.allow.room.for.mounting.the.phone..
•. Align.the.mounting.slots.over.the.screws.and.
slide.the.base.down.into.place.as.shown.above.
45
Maintenance
Specifications
Operating temperature 32°.F.to.122°.F.(0°.C.to.50°.C)
Base
Charging cradle
PS-0035
Part number
Input voltage
Output voltage
Part number
Capacity
PS-0035
AC adapter
120V.AC,.60.Hz
8V.DC.@.300mA
BT-1007
120V.AC,.60.Hz
8V.DC.@.300mA
BT-1015
Battery pack
or
500mAh,.2.4V.DC
650mAh.2.4V.DC
Notes:
•.Use.only.the.supplied.AC.adapters.
•.Be.sure.to.use.the.proper.adapter.for.the.base.and.any.chargers.
•.Do.not.place.the.power.cord.where.it.creates.a.trip.hazard.or.where.it.could.become.chafed.and.create.a.fire.or.
electrical.hazard.
•.Do.not.place.the.base.in.direct.sunlight.or.subject.it.to.high.temperatures.
Battery Information
Battery life
With.average.use,.your.handset.battery.provides.more.than.ten.hours.of.talk.time.and.approximately.seven.days.
of.standby.time..You.can.achieve.optimum.battery.life.and.performance.by.returning.the.handset.to.the.base.or.
charging.cradle.after.each.use..When.your.handset.is.left.off.of.the.cradle,.the.battery.will.gradually.discharge.even.
if.the.handset.is.not.being.used..The.actual.talk.time.duration.will.be.reduced.in.proportion.to.the.amount.of.time.the.
handset.is.off.of.the.cradle.
46
Low battery alert
When.the.battery.pack.is.very.low,.the.phone.is.programmed.to.eliminate.functions.in.
order.to.save.power..When.Low Battery - Charge Handset.appears.in.the.handset.display.
and.the.phone.is.in.standby,.none.of.the.keys.will.operate..If.you.are.on.a.call,.complete.
your.conversation.as.quickly.as.possible,.and.return.the.handset.to.the.cradle.
The.battery.pack.needs.to.be.charged.when.the.empty.battery.icon.appears.
Cleaning the charging contacts
To.maintain.a.good.charge,.clean.the.charging.contacts.on.the.handset.
once.a.month..Dampen.a.cloth.with.plain.water..Gently.rub.the.damp.cloth.
over.the.charging.contacts.until.all.visible.dirt.is.removed..Dry.the.contacts.
thoroughly.before.returning.the.handset.to.the.cradle.
Caution: Do.not.use.paint.thinner,.alcohol,.or.other.chemical.products..
Contacts
Doing.so.may.discolor.the.surface.of.the.telephone.and.damage.the.finish..
Battery replacement and handling
With.average.use,.your.phone’s.battery.should.last.approximately.one.year..To.order.replacement.batteries,.please.
Caution:
•.Use.only.battery.pack.BT-1007.or.BT-1015.
•.Do.not.remove.the.batteries.from.the.handset.to.charge.them..
•.Never.throw.the.battery.into.a.fire,.disassemble,.or.heat.them..
•.Do.not.remove.or.damage.the.battery.casing..
Power Failures
During.a.power.failure,.you.will.not.be.able.to.make.or.receive.calls.with.the.phone..To.avoid.damage.from.an.
electrical.spike.when.the.power.comes.back.on,.we.recommend.you.unplug.your.phone.during.power.outages.
47
Troubleshooting
Common Issues
If.your.phone.is.not.performing.to.your.expectations,.please.try.these.simple.steps.first..If.these.steps.do.not.solve.
your.problem,.please.call.our.Customer.Hotline.(see.the.back.cover.for.contact.information).
When you have this
Try...
problem...
The.charge.LED.won’t.
illuminate.when.the.handset.
•.Re-seating.the.handset.in.the.cradle..
is.placed.in.the.cradle.
•.Checking.the.telephone.cord.connection..If.Check TEL Line.appears.on.the.
handset.display,.the.telephone.cord.may.not.be.connected.correctly.(see.page.
10).
No.handsets.can.make.or.
receive.calls..
•.Disconnecting.the.base.AC.adapter..Wait.a.few.minutes,.then.reconnect.it.(see.
A.single.handset.can’t.make.
or.receive.calls.(but.other.
handsets.can).
•.Moving.the.handset.closer.to.the.base.
A.handset.can.make.calls,.
but.it.doesn’t.ring.or.receive.
a.page.
•.Checking.the.battery.pack.connection.(see.page.7).
•.Charging.the.battery.for.15-20.hours.
A.handset.is.not.working.
•.Resetting.the.handset.(see.page.51).
48
When you have this
problem...
Try...
•.Moving.the.handset.closer.to.the.base.
A.handset.says.Unavailable.
•.Seeing.if.another.handset.has.Privacy.Mode.turned.on.(see.page.40).
•.Making.sure.the.base.is.plugged.in.(see.page.8).
The.phone.keeps.ringing.
when.I.answer.on.an.
extension.
•.You.may.have.to.change.the.line.mode..Contact.customer.service.for.more.
information.(see.page.53).
•.Checking.to.see.if.the.call.was.placed.through.a.switchboard.
No.handsets.will.display.any. •.Asking.your.telephone.company.to.verify.your.Caller.ID.service.is.current..There.
Caller.ID.information.
may.be.a.problem.with.your.Caller.ID.service.
•.Letting.incoming.calls.ring.at.least.twice.before.answering.
Caller.ID.displays.briefly.and. •.You.may.have.to.change.the.line.mode..Contact.customer.service.for.more.
then.clears.
information.(see.page.53).
•.Seeing.if.you.already.have.6.handsets.registered.to.this.base.
•.Seeing.if.you.already.registered.this.handset.to.4.bases.
I.can’t.register.a.handset.at.
the.base.
A.handset.doesn’t.
communicate.with.other.
handsets..
•.Making.sure.all.handsets.are.registered.to.and.currently.connected.to.the.same.
base.(see.pages.14.and.15).
•.Resetting.the.problem.handsets.(see.page.51).
•.Making.sure.all.handsets.are.registered.to.and.currently.connected.to.the.same.
base.(see.pages.14.and.15).
I.can’t.transfer.calls.
•.Resetting.the.problem.handsets.(see.page.51).
49
When you have this
problem...
Try...
•.Checking.to.see.that.there.are.not.two.handsets.already.using.the.conference.
•.Making.sure.both.handsets.are.registered.to.and.currently.connected.to.the.same.
I.can’t.get.two.handsets.to.
talk.to.an.outside.caller.
The.new message.LED.
(Voice.Mail.Waiting.Indicator).
flashes,.but.there.are.no.new.
messages.
•..Resetting.the.Voice.Mail.Waiting.Indicator.(see.page.43).
Weak or Hard to Hear Audio
If.the.caller’s.voice.sounds.weak.or.soft,.the.signal.might.be.blocked.by.large.metal.objects.or.walls;.you.might.also.
be.too.far.from.the.base,.or.the.handset’s.battery.may.be.weak.
•.Try.adjusting.the.volume.of.the.earpiece.(see.page.36).or.the.audio.tone.(see.page.37).
•.Try.moving.around.while.you’re.on.a.call.or.moving.closer.to.the.base.to.see.if.the.sound.gets.louder.
•.Make.sure.the.handset’s.battery.is.fully.charged.
Noise or Static on the Line
The.most.common.cause.of.noise.or.static.on.a.cordless.phone.is.interference:.other.wireless.or.electronic.devices.
can.radiate.energy.that.disturbs.the.radio.signal.between.the.base.and.the.handset.(much.like.overhead.power.lines.
can.cause.static.on.your.car.radio)..Some.common.household.sources.of.interference.are
•.electrical.appliances,.especially.microwave.ovens.
•.computer.equipment,.especially.wireless.LAN.equipment.and.DSL.modems
•.radio-based.wireless.devices,.such.as.room.monitors,.wireless.controllers,.or.wireless.headphones.or.speakers
•.large.fluorescent.light.fixtures.(particularly.ones.that.give.off.a.“buzzing”.noise)
•.other.services.that.use.your.phone.line,.like.alarm.systems,.intercom.systems,.or.broadband.Internet.service
50
For.static.on.only.one.handset.or.in.a.specific.location:. For.static.on.more.than.one.handset:
•.Check.nearby.for.one.of.the.common.interference.
sources.
•.Try.moving.the.handset.away.from.a.suspected.
•.Check.near.the.base.for.the.source.of.interference.
•.Try.moving.the.base.away.from.a.suspected.source,.
or.try.turning.off.the.source.if.possible.
source,.or.try.moving.the.suspected.source.so.it’s.not. •.If.you.have.any.services.that.might.use.your.phone.
between.the.handset.and.the.base.
line,.see.if.you.need.a.filter.on.the.phone.line.
Installing a telephone line filter or DSL filter
Any.broadband.Internet.service.that.uses.your.telephone
line.might.interfere.with.standard.phones..The.most.common.
type.of.these.services,.DSL,.often.causes.static.on.your.
telephone..Fortunately,.an.easy-to-install.filter.removes.this.
static.from.the.line..Technicians.who.install.DSL.service.
usually.leave.several.filters.for.the.customers;.if.you.can’t.
find.them,.call.your.DSL.provider.or.look.in.any.electronics.
store.
Telephone
wall jack
Telephone
cord
DSL filter
Just.plug.the.DSL.filter.into.the.telephone.wall.jack.and.then.
plug.your.phone’s.base.into.the.filter..Make.a.test.call.to.
make.sure.the.noise.is.gone.
Resetting the Handset
You.may.need.to.reset.your.handset.in.the.following.instances:
•.You.lose.a.handset.and.purchase.a.new.one.
•.You.get.the.message.Registration.Failed.when.you.try.to.register.the.handset.
•.You.are.unable.to.register.any.handsets.to.the.base.
•.When.you.register.new.handsets.to.the.base,.the.handset.IDs.do.not.match..(For.example,.the.handset.registers.
as.“Handset.#4”.but.you.only.have.two.handsets.)
•.When.you.are.instructed.to.by.one.of.Uniden’s.call.center.representatives.
51
2).Press.and.hold.END.and.#.for.more.than.five.seconds..Select.Deregister HS.
3).Select.the.handset.which.you.are.operating,.and.then.press.MENU/SELECT.
4).The.phone.will.ask.you.to.confirm.the.deregistration..Select.Yes..The.selected.handset.will.clear.its.registration.
information.only.from.the.base.it.is.currently.connected.to,.and.then.delete.the.link.to.the.base.from.its.own.
memory.
5).When.the.base.information.is.deleted,.the.handset.displays.Handset not registered-place handset on base to
register. See your Owner's Manual for help.
If.the.handset.cannot.contact.the.base,.it.will.display.Out Of Range..Make.sure.the.handset.is.in.range.of.the.base.
and.the.base.is.connected.to.power;.you.can.also.reset.the.handset.without.the.base.(see.the.next.section).
Resetting the Handset Without the Base
If.your.original.base.is.not.available.for.some.reason,.you.can.still.reset.the.handset.and.use.it.with.another.base.
1).Press.and.hold.END.and.#.for.at.least.five.seconds.
2).Move.the.cursor.to.select.Base Unavailable.and.then.press.MENU/SELECT.
3).Select.the.base.which.you.want.to.de-register.from,.and.then.press.MENU/SELECT..Base Unavailable.appears.
4).Move.the.cursor.to.select.Yes,.and.then.press.MENU/SELECT..You.hear.a.confirmation.tone,.and.the.handset.
deletes.its.own.base.information.without.contacting.the.base..If.the.handset.was.registered.to.only.one.base,.
it.displays.Handset not registered-place handset on base to register. See your Owner's Manual for help..If.the.
handset.is.still.registered.to.another.base,.it.searches.for.the.other.base.and.then.returns.to.standby.
52
Changing the Line Mode for Multiple Extensions
Line.mode.refers.to.the.method.that.telephones.use.to.signal.each.other.that.an.extension.is.in.use..Customer.
service.may.recommend.changing.the.line.mode.if.you.have.any.of.the.following.problems:
•.Your.phone.keeps.ringing.after.someone.answers.on.an.extension.phone.
•.Your.answering.system.doesn’t.stop.recording.when.you.answer.on.an.extension.phone.
•.Caller.ID.displays.briefly.and.then.clears.
1).If.you.have.multiple.bases,.select.the.base.that.is.having.problems.(see.page.15).
2).Press.MENU/SELECT..
3).Select.the.Global Setup.menu,.and.then.the.Set Line Mode.submenu..
4).If Instructed by Customer Service Press [select].appears..Press.MENU/SELECT.
5).Move.the.cursor.to.select.Type - A,.Type - B,.or.Off.
6).Press.MENU/SELECT..You.will.hear.a.confirmation.tone.
Traveling Out of Range
When.the.handset.is.in.standby,.the.handset.will.display.Out Of Range.
During.a.call,.if.you.move.your.handset.too.far.from.your.base,.noise.may.increase..If.you.pass.the.range.limit.of.the.
base,.the.handset.will.beep,.display.Out Of Range,.and.then.go.to.standby..The.base.will.maintain.the.connection.
for.thirty.seconds.after.the.handset.goes.out.of.range..If.you.move.the.handset.back.within.range.of.the.base.within.
thirty.seconds,.press.TALK/FLASH.or. .to.pick.up.the.call.again.
Note:.. If.it.is.set.to.automatically.select.the.available.base,.the.handset.will.begin.searching.for.another.base.thirty.
seconds.after.going.out.of.range..(see.Selecting.the.base.on.page.15).
53
Liquid Damage
Moisture.and.liquid.can.damage.your.cordless.phone.
•.If.the.handset.or.base.is.exposed.to.moisture.or.liquid,.but.only.the.exterior.plastic.housing.is.affected,.wipe.off.
the.liquid,.and.use.as.normal..
•.If.moisture.or.liquid.has.entered.the.plastic.housing.(i.e..liquid.can.be.heard.in.the.phone.or.liquid.has.entered.the.
handset.battery.compartment.or.vent.openings.on.the.base),.follow.the.steps.below..After.following.these.steps,.if.
your.cordless.telephone.does.not.work,.please.call.our.Customer.Service.Hotline.(see.the.back.cover.page).
Handset
Base
1).Remove.the.battery.cover.and.leave.it.off.for.
1).Disconnect.the.AC.adapter.from.the.base,.cutting.
ventilation.
off.electrical.power.
2).Disconnect.the.battery.pack..Leave.the.battery.
cover.off.and.the.battery.pack.disconnected.for.at.
least.3.days.
2).Disconnect.the.telephone.cord.from.the.base.
3).Let.dry.for.at.least.3.days..
3).Once.the.handset.is.completely.dry,.reconnect.the.
battery.pack.and.the.battery.cover.
4).Recharge.the.handset’s.battery.pack.for.15.to.20.
hours.before.using..
IMPORTANT:.You.must.unplug.the.telephone.line.while.recharging.the.battery.packs.to.avoid.charge.interruption.
CAUTION: DO NOT use a microwave oven to speed up the drying process. This will cause permanent
damage to the handset, base and the microwave oven.
54
Rechargeable Nickel-Cadmium
Batteries Must Be Recycled or
Disposed of Properly
Precautions!
Before.you.read.anything.else,.please.observe.the.following:
Warning!
•. Uniden.voluntarily.participates.in.an.RBRC®.
industry.program.to.collect.and.recycle.nickel-cadmium.
batteries.at.the.end.of.their.useful.life,.when.taken.out.of.
service.within.the.United.States..
Uniden.America.Corporation.DOES.NOT.represent.this.unit.
to.be.waterproof..To.reduce.the.risk.of.fire,.electrical.shock,.
or.damage.to.the.unit,.DO.NOT.expose.this.unit.to.rain.or.
moisture.
•. The.RBRC®.program.provides.a.convenient.alternative.to.
placing.used.nickel-cadmium.batteries.into.the.trash.or.
municipal.waste.stream,.which.is.illegal.in.some.areas.
•. Through.the.RBRC®.program,.Uniden.makes.it.easy.
for.you.to.drop.off.the.used.battery.at.local.retailers.of.
replacement.nickel-cadmium.batteries..You.may.also.
contact.your.local.recycling.center.for.information.on.
where.to.return.the.used.battery...
Please.call.1-800-8-BATTERY.for.information.on.Ni-Cd.
battery.recycling.in.your.area..Uniden’s.involvement.in.
this.program.is.part.of.its.commitment.to.protecting.our.
environment.and.conserving.natural.resources.
•. RBRC®.is.a.registered.trademark.of.the.Rechargeable.
Battery.Recycling.Corporation.
Rechargeable Nickel-Cadmium Battery
Warning
•. This.equipment.contains.a.rechargeable.nickel-cadmium.
battery..
•. The.rechargeable.batteries.contained.in.this.equipment.
may.explode.if.disposed.of.in.a.fire..
•. Nickel.and.Cadmium.are.a.chemical.known.to.state.of.
California.to.cause.cancer..
•. Do.not.short-circuit.the.battery..
•. Do.not.charge.the.rechargeable.battery.pack.used.in.
this.equipment.with.in.any.charger.other.than.the.one.
designed.to.charge.this.battery.pack.as.specified.in.the.
owner's.manual..Using.another.charger.may.damage.the.
battery.pack.or.cause.the.battery.pack.to.explode..
Rechargeable.Batteries.Must.Be.Recycled.or.Disposed.of.
Properly..
Uniden.works.to.reduce.lead.content.in.our.PVC.coated.cords.
in.our.products.and.accessories.
Warning!
The.cords.on.this.product.and/or.accessories.contain.lead,.a.
chemical.known.to.the.State.of.California.to.cause.birth.defects.
or.other.reproductive.harm..Wash.hands.after.handling.
55
Important Safety Instructions
The FCC Wants You To Know
This.equipment.complies.with.Part.68.of.the.FCC.rules.and.
the.requirements.adopted.by.the.ACTA..On.the.bottom.of.this.
equipment.is.a.label.that.contains,.among.other.information,.a.
product.identifier.in.the.format.US:.AAAEQ##TXXXX..If.requested,.
this.number.must.be.provided.to.the.telephone.company.
When.using.your.telephone.equipment,.basic.safety.
precautions.should.always.be.followed.to.reduce.the.risk.
of.fire,.electric.shock.and.injury.to.persons,.including.the.
following:.
1.. Do.not.use.this.product.near.water,.for.example,.near.
a.bath.tub,.wash.bowl,.kitchen.sink.or.laundry.tub,.in.a.
wet.basement.or.near.a.swimming.pool..
An.applicable.Universal.Service.Order.Codes.(USOC).certification.
for.the.jacks.used.in.this.equipment.is.provided.(i.e.,.RJ11C).in.
the.packaging.with.each.piece.of.approved.terminal.equipment..
A.plug.and.jack.used.to.connect.this.equipment.to.the.premises.
wiring.and.telephone.network.must.comply.with.the.applicable.FCC.
Part.68.rules.and.requirements.adopted.by.the.ACTA..A.compliant.
telephone.cord.and.modular.plug.is.provided.with.this.product..It.is.
designed.to.be.connected.to.a.compatible.modular.jack.that.is.also.
compliant..See.installation.instructions.for.details.
2.. Avoid.using.a.telephone.(other.than.a.cordless.type).
during.an.electrical.storm..There.may.be.a.remote.risk.
of.electric.shock.from.lightning..
3.. Do.not.use.the.telephone.to.report.a.gas.leak.in.the.
vicinity.of.the.leak..
4.. Use.only.the.power.cord.and.batteries.indicated.in.
this.manual..Do.not.dispose.of.batteries.in.a.fire..They.
may.explode..Check.with.local.authorities.for.possible.
battery.disposal.instructions..
The.REN.is.used.to.determine.the.number.of.devices.that.may.be.
connected.to.a.telephone.line..Excessive.RENs.on.a.telephone.line.
may.result.in.the.devices.not.ringing.in.response.to.an.incoming.
call..In.most.but.not.all.areas,.the.sum.of.RENs.should.not.exceed.
five.(5.0)..To.be.certain.of.the.number.of.devices.that.may.be.
connected.to.a.line,.as.determined.by.the.total.RENs,.contact.the.
telephone.provider..For.products.approved.after.July.23,.2001,.the.
REN.for.this.product.is.part.of.the.product.identifier.that.has.the.
format.US:AAAEQ##TXXXX..The.digits.represented.by.##.are.the.
REN.without.a.decimal.point.(e.g.,.03.is.a.REN.of.0.3)..For.earlier.
products,.the.REN.is.separately.shown.on.the.label.
5.. Do.not.disassemble.any.component.of.this.product.
SAVE THESE INSTRUCTIONS
CAUTION..
Risk.of.explosion.if.battery.is.replaced.by.an.incorrect.type..
Dispose.of.used.batteries.according.to.the.instructions..Do.not.
open.or.mutilate.the.battery,.and.disconnect.the.battery.before.
shipping.this.product.
If.this.equipment.causes.harm.to.the.telephone.network,.the.
telephone.company.will.notify.you.in.advance.that.temporary.
discontinuance.of.service.may.be.required..But.if.advance.notice.
isn’t.practical,.the.telephone.company.will.notify.the.customer.as.
soon.as.possible..Also,.you.will.be.advised.of.your.right.to.file.a.
complaint.with.the.FCC.if.you.believe.it.is.necessary..The.telephone.
56
company.may.make.changes.in.its.facilities,.equipment,.operations.
or.procedures.that.could.affect.the.operation.of.the.equipment..If.
this.happens.the.telephone.company.will.provide.advance.notice.
in.order.for.you.to.make.necessary.modifications.to.maintain.
uninterrupted.service.
To.insure.the.safety.of.users,.the.FCC.has.established.criteria.
for.the.amount.of.radio.frequency.energy.various.products.may.
produce.depending.on.their.intended.usage..This.product.has.
been.tested.and.found.to.comply.with.the.FCC’s.exposure.criteria..
For.body.worn.operation,.the.FCC.RF.exposure.guidelines.were.
also.met.when.used.with.the.Uniden.accessories.supplied.or.
designed.for.this.product..Use.of.other.accessories.may.not.ensure.
compliance.with.FCC.RF.exposure.guidelines.and.should.be.
avoided.
Please.follow.instructions.for.repairing,.if.any.(e.g..battery.
replacement.section);.otherwise.do.not.substitute.or.repair.any.
parts.of.the.device.except.as.specified.in.this.manual..Connection.
to.party.line.service.is.subject.to.state.tariffs..Contact.the.state.
public.utility.commission,.public.service.commission.or.corporation.
commission.for.information..This.equipment.is.hearing.aid.
compatible.
The.antenna(s).used.for.the.base-unit.must.be.installed.to.provide.
a.separation.distance.of.at.least.20.cm.from.all.persons.and.must.
not.be.collocated.or.operated.in.conjunction.with.any.other.antenna.
or.transmitter.
Should.you.experience.trouble.with.this.equipment,.please.contact.
Uniden.customer.service.at.800-297-1023..If.the.equipment.is.
causing.harm.to.the.telephone.network,.the.telephone.company.
may.request.that.you.disconnect.the.equipment.until.the.problem.is.
resolved..
If.your.home.has.wired.alarm.equipment.connected.to.a.phone.
line,.be.sure.that.installing.the.system.does.not.disable.your.alarm.
equipment..If.you.have.questions.about.what.will.disable.alarm.
equipment,.contact.your.telephone.company.or.a.qualified.installer.
NOTICE:.According.to.telephone.company.reports,.AC.electrical.
surges,.typically.resulting.from.lightning.strikes,.are.very.destructive.
to.telephone.equipment.connected.to.AC.power.sources..To.
minimize.damage.from.these.types.of.surges,.a.surge.arrestor.is.
recommended.
Note:.This.equipment.has.been.tested.and.found.to.comply.with.the.
limits.for.a.Class.B.digital.device,.pursuant.to.part.15.of.the.FCC.
Rules..These.limits.are.designed.to.provide.reasonable.protection.
against.harmful.interference.in.a.residential.installation..This.
equipment.generates,.uses.and.can.radiate.radio.frequency.energy.
and,.if.not.installed.and.used.in.accordance.with.the.instructions,.
may.cause.harmful.interference.to.radio.communications..However,.
there.is.no.guarantee.that.interference.will.not.occur.in.a.particular.
installation..If.this.equipment.does.cause.harmful.interference.to.
radio.or.television.reception,.which.can.be.determined.by.turning.
the.equipment.off.and.on,.the.user.is.encouraged.to.try.to.correct.
the.interference.by.one.or.more.of.the.following.measures:
Changes.or.modifications.to.this.product.not.expressly.approved.
by.Uniden,.or.operation.of.this.product.in.any.way.other.than.as.
detailed.by.the.owner’s.manual,.could.void.your.authority.to.operate.
this.product.
This.device.complies.with.part.15.of.the.FCC.rules..Operation.
is.subject.to.the.following.two.conditions:.(1).This.device.may.
not.cause.harmful.interference,.and.(2).This.device.must.accept.
any.interference.received,.including.interference.that.may.cause.
undesired.operation..Privacy.of.communications.may.not.be.
ensured.when.using.this.phone.
--Reorient.or.relocate.the.receiving.antenna.
--Increase.the.separation.between.the.equipment.and.receiver.
57
--Connect.the.equipment.into.an.outlet.on.a.circuit.different.from..
...that.to.which.the.receiver.is.connected.
I.C. Notice
Terminal equipment
--Consult.the.dealer.or.an.experienced.radio/TV.technician.for.help.
NOTICE:.This.equipment.meets.the.applicable.Industry.
Canada.Terminal.Equipment.Technical.Specifications..This.is.
confirmed.by.the.registration.number..The.abbreviation,.IC,.
before.the.registration.number.signifies.that.registration.was.
performed.based.on.a.Declaration.of.Conformity.indicating.that.
Industry.Canada.technical.specifications.were.met..It.does.not.
imply.that.Industry.Canada.approved.the.equipment.
Radio interference
Radio.interference.may.occasionally.cause.buzzing.and.humming.
in.your.cordless.handset,.or.clicking.noises.in.the.base..This.
interference.is.caused.by.external.sources.such.as.TV,.refrigerator,.
vacuum.cleaner,.fluorescent.lighting,.or.electrical.storm..Your.unit.is.
NOT.DEFECTIVE..If.these.noises.continue.and.are.too.distracting,.
please.check.around.your.home.to.see.what.appliances.may.be.
causing.the.problem..In.addition,.we.recommend.that.the.base.
not.be.plugged.into.a.circuit.that.also.powers.a.major.appliance.
because.of.the.potential.for.interference..In.the.unlikely.event.that.
you.consistently.hear.other.voices.or.distracting.transmissions.
on.your.phone,.you.may.be.receiving.radio.signals.from.another.
cordless.telephone.or.other.source.of.interference.
NOTICE:.The.Ringer.Equivalence.Number.(REN).for.this.
terminal.equipment.is.marked.on.the.equipment.itself..The.REN.
assigned.to.each.terminal.equipment.provides.an.indication.
of.the.maximum.number.of.terminals.allowed.to.be.connected.
to.a.telephone.interface..The.termination.on.an.interface.may.
consist.of.any.combination.of.devices.subject.only.to.the.
requirement.that.the.sum.of.the.Ringer.Equivalence.Numbers.
of.all.the.devices.does.not.exceed.five.
Finally,.it.should.be.noted.that.some.cordless.telephones.operate.
at.frequencies.that.may.cause.interference.to.nearby.TVs.and.
VCRs..To.minimize.or.prevent.such.interference,.the.base.of.the.
cordless.telephone.should.not.be.placed.near.or.on.top.of.a.TV.or.
VCR..If.interference.is.experienced,.moving.the.cordless.telephone.
farther.away.from.the.TV.or.VCR.will.often.reduce.or.eliminate.the.
interference..
Radio equipment
The.term.“IC:”.before.the.radio.certification.number.only.signifies.
that.Industry.Canada.technical.specifications.were.met.
Cordless telephone privacy
Operation.is.subject.to.the.following.two.conditions:.(1).this.
device.may.not.cause.interference,.and.(2).this.device.must.
accept.any.interference,.including.interference.that.may.cause.
undesired.operation.of.the.device..“Privacy.of.communications.
may.not.be.ensured.when.using.this.telephone.”
Cordless.telephones.are.radio.devices..Communications.between.
the.handset.and.base.of.your.cordless.telephone.are.accomplished.
by.means.of.radio.waves.which.are.broadcast.over.the.open.
airways..Because.of.the.inherent.physical.properties.of.radio.
waves,.your.communications.can.be.received.by.radio.receiving.
devices.other.than.your.own..
cordless.telephone.unit..Consequently,.any.communications.using.
your.cordless.telephone.may.not.be.private.
58
A.PARTICULAR.PURPOSE..THIS.WARRANTY.DOES.
NOT.COVER.OR.PROVIDE.FOR.THE.REIMBURSEMENT.
OR.PAYMENT.OF.INCIDENTAL.OR.CONSEQUENTIAL.
DAMAGES..
One Year Limited Warranty
Important:.Evidence.of.original.purchase.is.required.for.
warranty.service..WARRANTOR:.UNIDEN.AMERICA.
CORPORATION.(“Uniden”).ELEMENTS.OF.WARRANTY:.
Uniden.warrants,.for.one.year,.to.the.original.retail.owner,.
this.Uniden.Product.to.be.free.from.defects.in.materials.and.
craftsmanship.with.only.the.limitations.or.exclusions.set.out.
below..WARRANTY.DURATION:.This.warranty.to.the.original.
user.shall.terminate.and.be.of.no.further.effect.12.months.
after.the.date.of.original.retail.sale..The.warranty.is.invalid.if.
the.Product.is.(A).damaged.or.not.maintained.as.reasonable.
or.necessary,.(B).modified,.altered,.or.used.as.part.of.any.
conversion.kits,.subassemblies,.or.any.configurations.not.sold.
by.Uniden,.(C).improperly.installed,.(D).serviced.or.repaired.by.
someone.other.than.an.authorized.Uniden.service.center.for.a.
defect.or.malfunction.covered.by.this.warranty,.(E)
Some.states.do.not.allow.this.exclusion.or.limitation.of.
incidental.or.consequential.damages.so.the.above.limitation.or.
exclusion.may.not.apply.to.you.
LEGAL.REMEDIES:.This.warranty.gives.you.specific.legal.
rights,.and.you.may.also.have.other.rights.which.vary.from.
state.to.state..This.warranty.is.void.outside.the.United.States.
of.America.and.Canada..PROCEDURE.FOR.OBTAINING.
PERFORMANCE.OF.WARRANTY:.If,.after.following.the.
instructions.in.the.owner’s.manual.you.are.certain.that.the.
Product.is.defective,.pack.the.Product.carefully.(preferably.
in.its.original.packaging)..Disconnect.the.battery.from.the.
Product.and.separately.secure.the.battery.in.its.own.separate.
packaging.within.the.shipping.carton..The.Product.should.
include.all.parts.and.accessories.originally.packaged.with.the.
Product..Include.evidence.of.original.purchase.and.a.note.
describing.the.defect.that.has.caused.you.to.return.it..The.
Product.should.be.shipped.freight.prepaid,.by.traceable.means,.
to.warrantor.at:.
used.in.any.conjunction.with.equipment.or.parts.or.as.part.of.
any.system.not.manufactured.by.Uniden,.or.(F).installed.or.
programmed.by.anyone.other.than.as.detailed.by.the.owner’s.
manual.for.this.product..STATEMENT.OF.REMEDY:.In.the.
event.that.the.product.does.not.conform.to.this.warranty.at.
any.time.while.this.warranty.is.in.effect,.warrantor.will.either,.
at.its.option,.repair.or.replace.the.defective.unit.and.return.
it.to.you.without.charge.for.parts,.service,.or.any.other.cost.
(except.shipping.and.handling).incurred.by.warrantor.or.its.
representatives.in.connection.with.the.performance.of.this.
warranty..Warrantor,.at.its.option,.may.replace.the.unit.with.
a.new.or.refurbished.unit..THE.LIMITED.WARRANTY.SET.
FORTH.ABOVE.IS.THE.SOLE.AND.ENTIRE.WARRANTY.
PERTAINING.TO.THE.PRODUCT.AND.IS.IN.LIEU.OF.
AND.EXCLUDES.ALL.OTHER.WARRANTIES.OF.ANY.
NATURE.WHATSOEVER,.WHETHER.EXPRESS,.IMPLIED.
OR.ARISING.BY.OPERATION.OF.LAW,.INCLUDING,.
BUT.NOT.LIMITED.TO.ANY.IMPLIED.WARRANTIES.OF.
MERCHANTABILITY.OR.FITNESS.FOR
Uniden America Service
4700.Amon.Carter.Blvd.
Fort.Worth,.TX.76155
59
O
S
P
Storing.Caller.ID.or.redial.
T
V
R
Redial
W
Ringer
61
Memo
62
Memo
63
VISIT OUR WEBSITE AT
WWW.UNIDEN.COM IF YOU...
• ...HAVE A QUESTION OR A PROBLEM.
Or call our Customer Hotline at 1-817-858-2929 or 1-800-297-1023 during regular business hours.*
• ...ARE LOOKING FOR A PART OR ACCESSORY.
Or call our Parts Department at 1-800-554-3988 during regular business hours.*
• ...NEED SPECIAL ASSISTANCE DUE TO A DISABILITY.
Or call our Accessibility help line at 1-800-874-9314 (voice or TTY).
© 2010 Uniden America Corp.,
Fort Worth, Texas. Printed In Vietnam.
* Central Standard Time. Detailed
customer service hours are available
|
Tektronix Printer 200E User Manual
Thermador Double Oven SEC271 User Manual
TP Link Network Card TL WA501G User Manual
Trane Thermostat XT500C User Manual
ViewSonic Flat Panel Television VS11778 User Manual
Viking Electronics Paint Sprayer C 1000A User Manual
Viking Oven F20812A EN User Manual
Volkswagen Automobile gr 10 User Manual
VTech Telephone LS6245 User Manual
Waterpik Technologies Electric Toothbrush WP 100 User Manual